Á¦Ç°¼Ò°³
¤ýÀÚ¼¼ÃøÁ¤ÀåÄ¡, IMU, GPS/INS
¤ý°í¼º´É MEMS °ü¼º ¼¾¼­, ½Ã½ºÅÛ ¹× ÅëÇÕ GPS
¤ý°íÃâ·Â ¹«¼± ÁõÆø±â
¤ýGNSS ½Ã¹Ä·¹ÀÌÅÍ, GNSS Test & Software Receiver
¤ýIP Core Á¦Ç°
¤ýÅë½ÅÄÉÀ̺í Æ÷¼³Àåºñ
¤ý½Ç³» À§Ä¡(ÃøÀ§) ÃßÀû ½Ã½ºÅÛ
¤ý¹«¼± µ¥ÀÌÅÍ Àü¼Û ½Ã½ºÅÛ
¤ý¼ö¼Ò ¸ÞÀÌÀú, ¼ö¼Ò ½Ã°è
¤ýGPS ½Ã°¢µ¿±âÈ­ Àåºñ
¤ýÃÊÁ¤¹Ð ½Ã°£ ÁÖÆļö Àåºñ
¤ý´ÙÁ߸ðµå¿ë Telemetry ¼Û/¼ö½Å±â
¤ýFilter Connector
  Global Partners
Exclusive Representative Contract
with Global Companies
°í¼º´É½Ã°£, ÁÖÆļö ºÐ¹è½Ã½ºÅÛ > Nim Modules
 
 
The HPDA-5 distribution amplifier exceeds the performance required to distribute state-of-the-art atomic frequency standards. The HPDA-5 offers 126 dB of channel to channel isolation and 135 dB of reverse isolation. The exceptionally low phase-noise -150 dBc/Hz at 1 Hz implies a short term frequency stability of 1 part in 1014 at 1 s. The HPDA-5 exhibits a low temperature coefficient of phase of 3 ps/¨¬C throughout the operating range. The input and outputs have a low VSWR to minimize environmental effects on frequency distribution through long transmission lines. The HPDA-5 is an enhanced version of the NIST high isolation distribution amplifier.The power supply requirements are +/- (12.5 to 15) VDC and +/-0.25 A. A "loss of signal" monitor line is available on the NIM backplane.

HPDA-5NM Users Manual
Specifications
Parameter
Conditions
Min

Typ

Max
Units
Input Power 1 db compression
17
18
-
dBm
Bandwidth +/-1 dB
1-20
-
-
MHz
Gain @5MHz
-
-
+/-0.5
dB
Impedance Input
Output
-
-
50
50
-
-
Ohms
Return loss Input(S11) 5 MHz
Output (S22) 5 MHz
-
-
-35
-25
-25
-25
dB
Distortion +13 dBm
+17dBm
-
-
-48
-40
-45
-
dBc
Isolation Output to output
Output to input
120
120
126
135
-
-
dB
Phase noise
Phase noise plot available here
1 Hz
10 Hz
1 kHz
10 kHz
-
-
-
-
-150
-160
-171
-172
-147
-157
-169
-170
dBc/Hz
Temperature-delay coefficient 0-50 ¡ÆC
25-35 ¡ÆC
-
-
3
1.5
5
-

ps/¡ÆC
All tests done at 5 MHz and +13 dBm input unless otherwise specified